Loading... Please wait...
- Home
- Accessories and Furniture
- Turntable Accessories
- Ortofon TA-210 Tonearm
)
Product Description
The new Ortofon TA-210 tonearm has gone to the next level of reducing unwanted vibrations in the tonearm by adding more damping material in more places when compared to it's younger sibling, the TA-110. Ortofon's extensive knowledge of vibration properties and characteristics in different shapes and materials has been applied for optimization of the TA-210 tonearm
The TA-210 is given a precision machined slit in each end of the aluminum tube. A piece of Ortofon special vibration damping compound is integrated into each slit. The bottom slit has rubber inserts with high vibration damping properties, and the other top-facing slit has a special proprietary TPE compound with excellent damping properties. Due to the use of these two different materials, an extended damping effect is obtained in the largest possible range. Both inserts integrated in the tonearm tube are manufactured at the Ortofon technical facilities in Nakskov, Denmark.
For more on the damping materials, click here.
Key Features:
- Supplied with LH-2000E headshell and 6NX-TSW-1010 tonearm cables
- TA-210 is a static balanced gimbal type arm, easy to use and adjust for optimal VTF settings
- TA-210 has a standard 5-pin DIN connector for tonearm cable
- The tonearm geometry allows for a Baerwald alignment (also the IEC recommendations)
- NEW - Counterweight with Inner/outer scale ♦ Inner scale to be applied with main counterweight
- ♦ Outer scale to be applied when extra mass ring is added
- Counterweight will work with headshell+cartridge mass approximately in the range 20 to 28g
- TA-210 is fitted with a standard headshell connector and can easily be adjusted in accordance with the included mounting template
- NEW - Extra mass ring for heavier cartridge and headshell combinations included (the extra mass ring may need to be attached to achieve proper tracking force)
- Extra mass ring weight 45g
Technical Data:
| Effective Mass (w/out Headshell): | 5g |
| Effective Armlength (Stylus - Pivot Point): | 329.0mm |
| Mounting Distance (Pivot Point - Turntable Centre): | 316.6mm |
| Offset Angle: | 16.5º |
| Overhang: | 12.4mm |
| Tracking Force Adjusting Range: | 0 - 3 / 0 - 4g |
| Height Adjustment Range: | 35 - 55mm |
| Armbase Mounting Hole Diameter: | 19 - 20mm |
| Diameter of the Tonearm Centre Shaft: | 18.0mm |
| Inner Null Point: | 66mm |
| Outer Null Point: | 120.9mm |
| Counterweight for Cart & Headshell Mass Between 21 and 28g: | Included |
| LH-2000E Headshell: | Included |
| Headshell Weight: | 15.5g |
| TA-110 Total Weight (Incl. Headshell) | 536g |
| Set of Tonearm Cables 6NX-TSW-1010: | Included |
| Extra Mass Ring for Heavier Cartridges: | Included |
| Extra Mass Ring Weight: | 45g |
How to Install the Extra Mass Ring:
The counterweight should be attached onto the rear of the tonearm with the inner number scale facing forward. If the extra mass ring is needed, it must be installed prior to attaching the counterweight to the tonearm. The extra mass ring should be installed on the back of the counterweight and may need to be twisted slightly to facilitate the installation. Ensure that the extra mass ring fits tightly to the thick part of the counterweight.
Product Videos
Warranty Information
Find Similar Products by Category
Related Products
-
Pro-Ject Cork-IT £20.00 -
Pro-Ject Clamp-IT £70.00 -
Pro-Ject Brush-IT £15.00 -
Pro-Ject Level-IT £20.00 -
Pro-Ject measure-IT 2 £90.00 -
Ortofon 2M Red Cartridge £95.00
